Buy Advanced Tool Design Model ATD-7007 220-Lbs. Capacity Heavy-Duty Portable Work TableAdvanced Tool Design Model ATD-7007 220-Lbs. Capacity Heavy-Duty Portable Work Table Product Description:
- Powder coat finish
- 2" Casters
Product Description
Adjusts from 34" to 47-3/4" for accessibility. 1" deep tray features dividers for 4 compartments. Has rubber corner bumpers to protect vehicle's finish.
Customer Reviews
Most helpful customer reviews
4 of 4 people found the following review helpful.
This thing is a beast
By DisplacedMic
I'm not sure i fully appreciated what i was getting when I ordered this table. i was expecting something a little flimsier. needless to say i was pleasantly surprised! this thing is a beast. right off the bat it was fairly poorly packaged - the box was in shambles. i was sure it was going to be a return. but this thing is so hardy that it made it through shipping w/ hardly a dent or scratch. one of the corners is bent a bit and the rubber stopper was pulled off but no big deal. it holds my tool box when i'm doing workshop stuff and it holds car junk when i'm working on my car. if i'm just tinkering in the garage i feel perfectly comfortable putting my laptop on it. really a handy little table to have around.It was super easy to put together, easy to adjust, relatively low profile and came with plenty of hardware to put it up. it took me about 5 minutes- casters on and 9 bolts to run down. easy.it's quite big and bulky but it's not really a storage model, but even in the short time i've had it i have already gotten used to it and use it regularly. haven't tried using it as a side table for my car tools - ie pushing the base under the car and have the table right there by the engine - but i see no reason why this wouldn't work. however i would definitely make sure it's immobilized because the cheap metal or plastic on your car is going to lose in a bump-battle with this thing.It is rated to 200-225 lbs center of the table and 50 out on the corners. i believe this is an accurate claim. i probably wouldn't put a 50 pound dumbbell on the very edge, but i wouldn't worry at all setting a tv in the middle of it...Another reviewer mentioned that the casters were too small - i haven't found that to be the case yet but I could certainly see it being a bit cumbersome to move loaded down - so far i have had no problems there - but i am just moving it around my smooth and level garage/workshop. i will say that i am considering swapping out the casters for ones w/ brakes or stoppers though...all in all i'm quite happy. i'd say you'd be hard pressed to do any serious damage to this thing...i might buy another one
2 of 2 people found the following review helpful.Good portable work table
By TB-10 Pilot
Very easy to assemble but I had to take off a couple stars for the following reasons.1) All the bolts, lock washers, washers, etc were in a sealed bag EXCEPT for the one and ONLY 17MM bolt that is used to connect the bottom rail! Considering the bag was sealed, and there were/are 8 14mm bolts, how hard is it to count to one (1) to include the one and only 17MM bolt? Now I have to drive to Lowes or Home Depot with the part to find a bolt that fits it. Not a big deal but it's an inconvenience.2) Not a mis-communication but there is no way to fold this thing when not in use. A folding flange with a push locking pin would have been easy to integrate to allow the top to fold down so it can at least be pushed and stowed against a wall without it sticking out.Be warned, because of the included non-slip mats which are a plus, it really smells a lot when you open it. I made the mistake of assembling it in my living room because of a hot day and wanted to be in A/C. My wife was none too pleased with the smell. But I'm sure it will go away once it's in the garage.
2 of 2 people found the following review helpful.Pretty Good Work Table
By Shannon - Tucson
I had to order a 2nd one because the 1st one came in with damage and was incomplete. Neither one the fault of the seller. The 2nd one came in with a small dent that is not noticeable and a broken push button retainer on the corner. The cart is very functional and works great in my shop. Rolls smooth and holds up well. This one is MADE IN CHINA. I prefer and try to buy MADE IN THE USA as much as possible but this type of table is currently not made in the USA.
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!
